Monday, June 4, 2012

Project Compendium Hive Tyrant Wings

Hive Tyrant wings with scything talons.

This project is now dead with the release of a plastic GW flying tyrant kit.

First is a reference photo of the large scything talon from the Trygon kit.

Top view ready for first layer of thin sheet polystyrene to build the wing webbing.

Next a top down view, dry fit onto a hive tyrant.

Top down view comparison against a Balrog wing conversion.

Frontal comparison.

Frontal comparison 2.

First layer of Green Stuff has been applied to the top of the wing, I used heavy paper to make the base of the webbing then soaked it with super glue to add strength.  The GS has been textured using wet sand-able sand paper being pressed into the GS to leave a rough even texture.

Paper membrane ready for Green Stuff

I realized that this is the largest GS project I have ever done. I have used GS often to fill gaps and reconstruct small missing details, but nothing of this scope.

On this side I still need to re-work the talon on the elbow, the inner arm webbing, and the attaching tendons to the finger bones.

More green stuff added, wings have been smoothed to remove previous texture.

Bottom side, starting to apply green stuff.

The steps between green stuff take a lot of time to dry, so I have started a second project.

Comparisons with Forgeworld warrior wings

After checking out the FW wings I have decided to match the style, the armor plates at the joints and elbow,  the armored section around the hand structure, and the way the membrane joins up to the skeletal/chitinous  structure

Project Compendium Tyranid Swarmlord

This is a compilation of the WiP posts for the Tyranid Swarmlord

I have been running two conversion projects at once, to fill the down time while waiting on green stuff to cure.

Starting Bitz;

I am going to be using a Trygon torso and 2 Trygon head plates (not pictured), plus a set of Carnifex legs and tail, standard Carnifex head and standard Carnifex armored plate (not pictured either).

Torso modifications:

I removed the 2nd and 3rd ridges from the armored plate,  I would later go on to remove the first two back vents as well.

Torso modifications step 2:

Here you can see the Carnifex armored plated and additional green stuff vent that has been added to the torso.  The Carnifex tail section has been lengthened so that the torso and tail/waist will fit correctly.  The tops of the Carnifex legs have been widened and Trygon head crests have been cut into armor plating for the thighs.

Leg conversion process
Thighs removed from legs
Thighs cut in half

The Carnifex thighs were removed with a jewelers saw, the cut in half with a standard hobby razor saw.  The thighs were then widened by gluing the halves to a 1/8 inch thick piece of plastic card and sculpting/sanding it down to match the original contour.  Your can see the white plastic card in a photo above this.

Trygon torso:
Beginning to blend the Carnifex armor plate into the torso and have added the first 2 green stuff vents.

Waist & Tail extended and armor plate added

Torso & Tail dry fit

The last two pairs of vents still need to be extended with GS.

Current edition Hive Tyrant tail
I need 2 of these and I don't want to pay for them as bitz on eBay.

Press Mold
I used Instant Mold to make a quick press mold.

I took a piece of brass rod and bent it to shape to be structural support of the tail.

Beginning to pack the mold with ProCreate at a 60/40 mix.

Two short tail sections molded up with brass rod inserts ready for use.

Legs about %85 complete

I need to fatten up the thighs a little bit, going for that softball player look.

Making the primary horn

Still need the extended goatee and talon thingies on the sides of the mouth

Tail section

Built up with brass rod and first layer of green stuff.

Update 4

Moar Head

Those wonderful mouth claw thingies
I still need to finish out the neck muscles.

Thickened thighs
Ready to be cast in resin.

Update 5

Resin Leg casts are finished........ Wooo

Size comparisons
So it looks like Swarmy is gonna be shorter than a Trygon / Mawloc and taller than a current Tyrant.  That is an original hive tyrant up front, I now use them as either tyranid primes or tyrant guard.

Face off
The torso still needs 4 more spore vents and the small chest plate claws.

Top down

Side view

Leg comparison
Current hive tyrant, custom leg set, carnifex.